Jeep Dashboard Symbols and Meaning (FULL list, Free Download)

This warning light will illuminate when the Stop/Start system is not functioning properly and service is required. Contact an authorized dealer for service.

This warning light will indicate when the ESC system is Active. The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN position, and when ESC is activated. It should go out with the engine running. If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.
● The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN position.
● The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive.
● This light will come on when the vehicle is in an ESC event.

The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed.
Should one or more tires be in the condition previously mentioned, the display will show the indications corresponding to each tire.
Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
As an added safety feature, your vehicle has been equipped with a TPMS that illuminates a low tire pressure telltale when one or more of your tires is significantly underinflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.

This light indicates that the transmission fluid temperature is running hot. This may occur with severe usages, such as trailer towing. If this light turns on, safely pull over and stop the vehicle. Then, shift the transmission into NEUTRAL and run the engine at idle or faster until the light turns off.

This warning light will illuminate when the ignition is in the ON/RUN position before the engine start. If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly.
Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after the engine start. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing.
When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.

This light will illuminate when there is a malfunction in one of the exterior bulbs.

This light illuminates when driver inattentiveness has been detected, warning the driver to place their hands on the steering wheel.

This light will illuminate when there is a fault detected in the air suspension system.

This warning light will illuminate to indicate the Electric Park Brake is not functioning properly and service is required. Contact an authorized dealer.

This warning light indicates the ESC is off.
Each time the ignition is turned to ON/RUN, the ESC system will be on, even if it was turned off previously.

This warning light monitors the ABS. The light will turn on when the ignition is placed in the ON/RUN or position and may stay on for as long as four seconds.
If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible. However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.
If the ABS light does not turn on when the ignition is placed in the ON/RUN position, have the brake system inspected by an authorized dealer.

This warning light will illuminate to signal a fault with the 4WD system. If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required. We recommend you drive to the nearest authorized dealer and have the vehicle serviced immediately.

This warning light will illuminate to indicate a fault in the FCW or PEB System. Contact an authorized dealer for service.

This light indicates that the maximum payload may have been exceeded or load leveling cannot be achieved at its current ride height.

This warning light will illuminate along with a dedicated message on the display (if equipped) if an unknown fluid not conforming with acceptable characteristics is inserted, or if an average consumption of AdBlue® (UREA) over 50% is detected. Contact an authorized dealer as soon as possible.
If the problem is not solved, a specific message will appear on the instrument cluster display whenever a certain threshold is reached until it will no longer be possible to start the engine.
When about 125 miles (200 km) are remaining before the AdBlue® (UREA) tank is empty, a continuous dedicated message will appear on the instrument panel, accompanied by a chime.

This light will turn on when the Active Driving Assist system has detected a fault.

The Active Lane Management Warning Light will be solid yellow when the vehicle is approaching a lane marker. The warning light will flash when the vehicle is crossing the lane marker.

This warning light will illuminate along with a dedicated message on the display if a problem is detected with the Fuel Level Sensor. If this light comes on, see an authorized dealer immediately.

When the fuel level reaches approximately 2 gal (7.5 L), this light will turn on and a chime will sound. The light will remain on until fuel is added.

This warning light will illuminate after an accident has occurred, and the system has shut the fuel off.

This light will illuminate if there is a fuel cutoff failure. If this light illuminates, take it to an authorized dealer and have them inspect it.

This warning light will illuminate when the windshield washer fluid is low.

The Night Vision Animal Warning Light will illuminate in yellow when an animal is approaching or is in the vehicle’s path.

The Night Vision Pedestrian Warning Light will illuminate in yellow when a pedestrian is approaching or is in the vehicle’s path.

This warning light will illuminate to signal a fault with the 4WD system. If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required. We recommend you drive to the nearest authorized dealer and have the vehicle serviced immediately.

This warning light will illuminate when the Active Lane Management system is not operating and requires service. Please see an authorized dealer.

This light will turn on when the ACC is not operating and needs service.

This light will illuminate when there is a fault in the sway bar disconnect system.

This light alerts the driver that the vehicle is in the 4WD Low mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels.

This light alerts the driver that the vehicle is in the 4WD Low mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels.

This light will illuminate when the air suspension system is actively adjusting the ride height.

This light will illuminate when the air suspension system is set to the Aerodynamic setting.

This light will illuminate when the vehicle is automatically lowered from ride height position downward for easy entry and exit of the vehicle.

This light will illuminate when the air suspension system is set to the Off-Road 1 setting.

This light will illuminate when the air suspension system is set to the Off-Road 2 setting.

The Auto HOLD! Fault Indicator light will illuminate if a fault is detected, it will be indicated by a yellow ‘HOLD!’ indicator light that will stay on as long as the fault condition exists.

This telltale will turn on to warn you of a possible collision with the vehicle in front of you.

This indicator light illuminates to indicate that FCW or PEB is off.

This indicator light illuminates to indicate that FCW or PEB is off.

This light alerts the driver that the 4WD power transfer case is in the NEUTRAL mode and the front and rear driveshafts are disengaged from the powertrain.

This light alerts the driver that the 4WD power transfer case is in the NEUTRAL mode and the front and rear driveshafts are disengaged from the powertrain.

This indicator light will illuminate when the front sway bar is disconnected.

This warning light will illuminate when the fuel filler cap is loose. Properly close the filler cap to disengage the light. If the light does not turn off, please see an authorized dealer.

This warning light will illuminate to indicate the Cruise Control system is not functioning properly and service is required. Contact an authorized dealer.

This light alerts the driver that the vehicle is in the Four-Wheel Drive (4WD) mode, and the front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.

This light alerts the driver that the vehicle is in the Four-Wheel Drive (4WD) mode, and the front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.

This light alerts the driver that the vehicle is in the Four-Wheel Drive part time mode, and the front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.

This light alerts the driver that the vehicle is in the Four-Wheel Drive part time mode, and the front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.

This light indicates when the front and/or rear axle locker fault has been detected.

This light indicates when the front, rear, or both axles have been locked. The telltale will display the lock icon on the front and rear axles to indicate the current lock status.

This light indicates when the rear axle lock has been activated

This light indicates when the rear axle lock has been activated

This indicator light will illuminate for approximately two seconds when the ignition is turned to the ON/RUN position. Its duration may be longer based on colder operating conditions. Vehicle will not initiate start until telltale is no longer displayed

The Low Diesel Exhaust Emissions Additive AdBlue® (UREA) indicator light illuminates when the AdBlue® (UREA) level is low. Fill the AdBlue® (UREA) tank as soon as possible with at least 1.3 gallons (5 liters) of AdBlue® (UREA).
If filling the tank is done with a remaining range of AdBlue® (UREA) in the tank equal to zero, you may need to wait two minutes before starting the vehicle.

The Water In Fuel Indicator Light will illuminate when there is water detected in the fuel filter. If this light remains on, DO NOT start the vehicle
before you drain the water from the fuel filter to prevent engine damage, and please see an authorized dealer.

This telltale will turn on to indicate the vehicle coolant level is low.

This light illuminates when there is a failure with the tow hook. Contact an authorized dealer for service.

This light alerts the driver that the vehicle is in the 4WD LOCK mode. The front and rear driveshafts are mechanically locked together, forcing the front and rear wheels to rotate at the same speed.

This telltale will illuminate when the Vehicle Security system has detected an attempt to break into the vehicle.

This indicator light will illuminate when Off Road+ has been activated.

This indicator light will illuminate when the Bed Lamp has been activated.

This light will illuminate to report a failure of the Audio System. Contact an authorized dealership as soon as possible.

This light will illuminate during an icy road condition.

The icon will appear on the instrument panel display to indicate overheating of the 4WD system. The mode selected by the user will be applied as soon as the system exits the overheating condition.

This symbol lights up (together with a dedicated message on display) when a dusk sensor malfunction is detected.

The malfunction indicator lamp for the ESP is combined with the BAS indicator. The yellow”ESP/BAS Warning Lamp” in the instrument cluster comes on when the ignition switch is turned to the “ON” position. It should go out with the engine running.
If the “ESP/BAS Warning Lamp” comes on continuously with the engine running, a malfunction has been detectedin either the ESP or the BAS system, or both. If this light remains on after several ignition cycles, and the vehiclehas been driven several miles at speeds greater than 30mph (48 km/h), see your authorized dealer as soon aspossible to have the problem diagnosed and corrected.